Given that most other TCs in the same IANA maintained MIB module
in fact DO have a enum of: unknown(2)
I can even see it would be very easy to make the case that it was
an error/omission that the PrtChannelTypeTC does not have it.
I do not see why this would need to take more than a few weeks
in fact. The addition (as far as I can tell) can be made by
expert review (to be designated by APPS ADs).
Do you want to give it a try?
Bert
> -----Original Message-----
> From: McDonald, Ira [mailto:imcdonald@sharplabs.com]
> Sent: Wednesday, July 20, 2005 17:38
> To: 'Bergman, Ron'; McDonald, Ira; Wijnen, Bert (Bert); pmp@pwg.org
> Subject: RE: PMP> Restructured Port MIB (18 July 2005)
>
>
> Hi Ron,
>
> Based on previous IPP experience, it will take MONTHS to add one
> new enum to the PrtChannelTypeTC with IANA - that would stop the
> Port Mon MIB dead in its tracks until it was accepted by IANA.
>
> About ppmPrinterEnabled - same rationale as ppmPortEnabled - keeps
> the number of Printer entries STATIC in an implementation - lets
> the user see that the one Printer (i.e., hardward output interface)
> on an External Network Adapter should presently be ignored.
>
> Remember that the Port Mon MIB MUST NOT depend on either Host
> Resources or Printer MIB, by common concensus - it may only
> AUGMENT them, if they are present.
>
> Cheers,
> - Ira
>
> Ira McDonald (Musician / Software Architect)
> Blue Roof Music / High North Inc
> PO Box 221 Grand Marais, MI 49839
> phone: +1-906-494-2434
> email: imcdonald@sharplabs.com
>
> > -----Original Message-----
> > From: Bergman, Ron [mailto:Ron.Bergman@rpsa.ricoh.com]
> > Sent: Tuesday, July 19, 2005 7:40 PM
> > To: McDonald, Ira; Wijnen, Bert (Bert); pmp@pwg.org
> > Subject: RE: PMP> Restructured Port MIB (18 July 2005)
> >
> >
> > Ira,
> >
> > I am not sure what value ppmPrinterEnabled adds to the MIB.
> > This appears to be analogous to
> > On Line/Off Line. If I want to create a driver for the
> > printer I don't care what the current
> > state is. That information is only necessary when I am ready
> > to print and then this MIB is
> > not used.
> >
> > I believe that Bert has a valid point in using
> > ppmPortProtocolType. It is not a major effort
> > to add unknown(2) to the IANA registrations.
> >
> > Otherwise, the changes are inline with our discussions
> > following the test.
> >
> > Ron
> >
> > -----Original Message-----
> > From: pmp-owner@pwg.org [mailto:pmp-owner@pwg.org]On Behalf
> > Of McDonald,
> > Ira
> > Sent: Tuesday, July 19, 2005 9:46 AM
> > To: 'Wijnen, Bert (Bert)'; McDonald, Ira; 'pmp@pwg.org'
> > Subject: RE: PMP> Restructured Port MIB (18 July 2005)
> >
> >
> > Hi Bert,
> >
> > Thanks for your quick feedback. My replies inline below.
> >
> > Cheers,
> > - Ira
> >
> >
> > Ira McDonald (Musician / Software Architect)
> > Blue Roof Music / High North Inc
> > PO Box 221 Grand Marais, MI 49839
> > phone: +1-906-494-2434
> > email: imcdonald@sharplabs.com
> >
> > > -----Original Message-----
> > > From: Wijnen, Bert (Bert) [mailto:bwijnen@lucent.com]
> > > Sent: Tuesday, July 19, 2005 9:08 AM
> > > To: McDonald, Ira; 'pmp@pwg.org'
> > > Subject: RE: PMP> Restructured Port MIB (18 July 2005)
> > >
> > >
> > > Only did a very very quick scan.
> > >
> > > Comments.
> > >
> > > - ppmPortProtocolTargetPort OBJECT-TYPE
> > > SYNTAX Integer32 (0..65535)
> > > I propose that you use InetPortNumber TC from RFC4001
> > >
> >
> > Won't work, because this port is not limited to Internet Suite
> > protocols. The 'service:' URI in ppmPortServiceNameOrURI may
> > also be for non-Internet suites (AppleTalk, NetWare, etc.).
> >
> > I'll correct the DESCRIPTION in the MIB and make clear that
> > (as with the Printer MIB) ports/channels may be from multiple
> > protocol suites.
> >
> >
> > > - ppmPortProtocolType OBJECT-TYPE
> > > SYNTAX Integer32 (0..2147483647)
> > >
> > > WHy not use TC PrtChannelTypeTC as the SYNTAX?
> > > I do see that you want to use zero (meaning not supported).
> > > But maybe better is to use none(1) in that case, or maybe
> > > adding an enumeration to the TC of notSupported(xx) ??
> > > It is now an IANA-maintained TC, so it should not be that
> > > difficult to get a label added.
> > >
> >
> > Won't work. PrtChannelTypeTC currently only defines 'other(1)'
> > and (foolishly) does NOT define 'unknown(2)' (unlike every other
> > textual convention in the Printer MIB). Because the Printer MIB
> > v2 still doesn't define DEFVAL clauses for most objects, this
> > oversight has not surfaced before. We could register 'unknown(2)'
> > with IANA, but _not_ fast enough (because this MIB's going into OS
> > and printer vendor products right now).
> >
> >
> > > - ppmPortPrtChannelIndex has a reference to RFC1213, while I
> > > think I would reather reference RFC2863 (the current IF-MIB)
> > >
> > > Bert
> > >
> >
> > Agreed. My mistake from the old Printer MIB (RFC 1759).
> >
> > I'll correct the references in the MIB.
> > - Ira
> >
>
This archive was generated by hypermail 2b29 : Wed Jul 20 2005 - 14:39:59 EDT