Hi,
A new draft should be available soon with these Design Requirements
for the Printer Port Monitor MIB, with help from Jerry Thrasher
(who chased me down to write them).
Cheers,
- Ira
Ira McDonald (Musician / Software Architect)
Blue Roof Music / High North Inc
PO Box 221 Grand Marais, MI 49839
phone: +1-906-494-2434
email: imcdonald at sharplabs.com
> -----Original Message-----
> From: McDonald, Ira
> Sent: Monday, June 06, 2005 1:28 PM
> To: 'thrasher at lexmark.com'; McDonald, Ira
> Subject: Design Reqs for Port MIB
>>> Hi Jerry, Monday (6
> June 2005)
>> Below are the updates for the Printer Port Monitor MIB:
>> (a) Two new informative references for section 9;
> (b) One new sentence for section 1.2 'Background';
> (c) One new section 1.3 'Design Requirements for PPM MIB' with forward
> references to section 2.4 'Use Models of PPM MIB' for
> derived design
> requirements;
> (d) Two typo corrections in section 2.3 'Structure of PPM MIB'.
>> Cheers,
> - Ira
>>> Ira McDonald (Musician / Software Architect)
> Blue Roof Music / High North Inc
> PO Box 221 Grand Marais, MI 49839
> phone: +1-906-494-2434
> email: imcdonald at sharplabs.com> --------------------------------------------------------------
> ----------
>> [add the following to beginning of section 9 'Informative References']
>> [MIB-GUIDE] Heard.
> IETF Guidelines for Authors and Reviewers of MIB Documents,
> work-in-progress, <draft-ietf-ops-mib-review-guidelines-xx.txt>.
>> [PORT-PROP] Fenelon, Pavicevic.
> Microsoft Port MIB proposal, November 2004.
>ftp://ftp.pwg.org/pub/pwg/BOFs/port/TCPMonMIBExtension.pdf (MIB)
>ftp://ftp.pwg.org/pub/pwg/BOFs/port/TCPMonPWG.ppt (slides)
>> --------------------------------------------------------------
> ----------
>> [add the following to the end of the last paragraph of section 1.2]
>> The initial Microsoft Port MIB proposal is archived at [PORT-PROP].
>> --------------------------------------------------------------
> ----------
>> [add the following new section after section 1.2]
>> 1.3 Design Requirements for PPM MIB
>> (1) The PPM MIB design MUST follow all object naming and MIB
> structuring
> requirements defined in IETF SMIv2 [RFC2578].
>> (2) The PPM MIB design SHOULD follow all best practices
> defined in IETF
> Guidelines for Authors and Reviewers of MIB Documents [MIB-GUIDE].
>> (3) The PPM MIB design SHOULD include all of the content
> defined in the
> Microsoft Port MIB proposal (see section 1.2).
>> (4) The PPM MIB design MUST NOT require implementation of any version
> of the IETF Host Resources [RFC1514] [RFC2790] or IETF Printer MIB
> [RFC1759] [RFC3805] (for low cost of implementation).
>> (5) The PPM MIB design MUST support automatic device driver
> installation
> by operating systems (see section 1.2 and section 2.4).
>> (6) The PPM MIB design MUST support status monitoring of
> Device entries
> in the IETF Host Resources [RFC1514] [RFC2790] (see section 2.4).
>> (7) The PPM MIB design MUST support status monitoring of
> General entries
> in the IETF Printer MIB [RFC1759] [RFC3805] (see section 2.4).
>> (8) The PPM MIB design SHOULD support access to Channel entries in the
> IETF Printer MIB [RFC1759] [RFC3805] (see section 2.4.3).
>> --------------------------------------------------------------
> ----------
>> [correct the following two typos in section 2.3 'Structure of
> PPM MIB']
>> change:
>> The PPM MIB defines three mandatory object groups:
> ^^^^^
>> General Group - two scalar objects
> ^^^
>> to:
>> The PPM MIB defines two mandatory object groups:
>> General Group - three scalar objects
>> --------------------------------------------------------------
> ----------
>