Hi Harry, hi Ira,
thank you for your information. It gives us a clear direction to proceed.
Best regards
Andreas
-----Ursprüngliche Nachricht-----
Von: Harry Lewis [mailto:harryl at us.ibm.com]
Gesendet: Montag, 28. Februar 2005 07:23
An: McDonald, Ira
Cc: 'Hirn, Andreas'; 'fin at pwg.org'; 'pmp at pwg.org';
'rbergma at hitachi-hkis.com'; technic at up3i.org
Betreff: RE: FIN> finisher mib integration into up3i
Ira says it better than I in my response to fin at pwg.org and validates my
opinion that option (1) is preferred.
----------------------------------------------
Harry Lewis
IBM STSM
Chairman - IEEE-ISTO Printer Working Group
http://www.pwg.org
IBM Printing Systems
http://www.ibm.com/printers
303-924-5337
----------------------------------------------
"McDonald, Ira" <imcdonald at sharplabs.com>
02/24/2005 09:32 AM
To
"'Hirn, Andreas'" <Andreas.Hirn at ops.de>, Harry Lewis/Boulder/IBM at IBMUS,
"'pmp at pwg.org'" <pmp at pwg.org>
cc
"'fin at pwg.org'" <fin at pwg.org>, "'rbergma at hitachi-hkis.com'"
<rbergma at hitachi-hkis.com>, technic at up3i.org
Subject
RE: FIN> finisher mib integration into up3i
Hi Andreas,
Thanks for your interesting question below.
I'm copying this reply to the Printer MIB Project (PMP)
mailing list. The Finisher MIB mailing list remains
functional, but has very few subscribers. All future
MIB work in the IEEE/ISTO PWG is being coordinated
through the PMP list.
Please note that the 'finSupplyTable' has a non-index
informational element 'finSupplyDeviceIndex' defined as:
"The value of finDeviceIndex corresponding to the finishing
device subunit with which this finisher supply is
associated.
The value zero indicates the associated finishing device is
Unknown."
And the 'finSupplyMediaInputTable' has a similar
informational element 'finSupplyMediaInputDeviceIndex'.
Those elements are NOT indices of their tables (and allowed
to take the value of zero), in case they are associated
with the overall finisher and not a specific finishing device.
It's certainly allowed to implement more than other printer
in 'hrDeviceTable' (and thus more than one complete print
line for alerts, trays, etc.). I think that's probably the
best way to separate the alerts/trays for individual finishers.
Note: We've tried to accomodate UP3I requests for counters
in our Imaging Device Counters spec, Counter Schema, and
Counter MIB work in the PWG WIMS working group. Comments
are very welcome.
ftp://ftp.pwg.org/pub/pwg/wims/wd/wd-wimscount10-20050120.pdfftp://ftp.pwg.org/pub/pwg/wims/wd/wd-wimscountmib10-20050205.htm
- full text - PWG boilerplate, introduction, model, references
ftp://ftp.pwg.org/pub/pwg/wims/wd/wd-wimscountmib10-20050205.mib
- ASN.1 MIB source only
Note that the Finisher subunit (the elements defined in the
Finisher MIB) has not yet been added to our Subunits schema.
ftp://ftp.pwg.org/pub/pwg/wims/schemas/subunits-20041212.xsd
Cheers,
- Ira (co-editor of Printer MIB v2 and Finisher MIB)
Ira McDonald (Musician / Software Architect)
Blue Roof Music / High North Inc
PO Box 221 Grand Marais, MI 49839
phone: +1-906-494-2434
email: imcdonald at sharplabs.com
-----Original Message-----
From: fin-owner at pwg.org [mailto:fin-owner at pwg.org]On Behalf Of Hirn,
Andreas
Sent: Thursday, February 24, 2005 10:42 AM
To: 'harryl at us.ibm.com'
Cc: 'fin at pwg.org'; 'rbergma at hitachi-hkis.com'; technic at up3i.org
Subject: FIN> finisher mib integration into up3i
Hi Harry,
UP3I is a standard to connect independent preprinter, printer and
postprocessing devices together to a printline like this:
+-------+
| |
| Host |
| |
+---+---+
|
|
| e.g. Ethernet LAN
|
|
+-------+ +---+---+ +-------+
| | | | | |
| pre a | ... |Printer| ... | post c| ....
| | | | | |
+---+---+ +---+---+ +---+---+
| | |
| | |
| | |
+-------...-------+------...--------+--------...
|
| 1394
|
+---+---+
| |
| UP3i |
|manager|
| |
+---+---+
|
|
| LAN
|
|
+---+---+
| |
| SNMP |
|manager|
| |
+---+---+
The commands between the preprinter, printer and postprocessing devices are
sent as standardized UP3I frames over a firewire cable. Every device has a
unique address in the system, called paper sequence id. It is also possible
to send SNMP requests packed into UP3I frames from the up3i manager to the
up3i devices and back. The up3i manager could also have a LAN interface.
Now we want to implement printer and finisher mib support into the print
line to allow an external SNMP manger to monitor the print line.
In the moment we have two ideas how we can do that:
1.) Stand alone devices
Every preprinter, printer and postprocessing device acts as a discrete
device in the host resources mib of the up3i manager. The hrDeviceIndex
could be the same as the paper sequence id. Every device itselfs implents
the host resources-, printer- and finisher mib, independant from the rest
of the print line. The snmp requests to the up3i manager are directly
handed over to the up3i devices by packing them into up3i snmp frames.
The problem with this solution is:
We don't know if it is allowed (respectively meaningful) to have a print
line in which every device has its own hrDeviceIndex. It seems that the
combination printer/finishing mib only allows one hrDeviceIndex per line
and several finDeviceIndex(es) for every device. Is it meaningful
regarding a SNMP Printer Manager to use several hrDeviceIndex instances
in a print line?
2.) One hrDeviceIndex per print line
We have one hrDeviceIndex for the printLine, the up3i device are separated
by their finDeviceIndex. The finDeviceIndex could be the same as the paper
sequence id.
The problems now are:
The finSupply/finSupplyMediaInput tables are not indexed by the
finDeviceIndex,
they have a separate finSupplyIndex/finSupplyMediaInputIndex. An agreement
is
needed which device can use which finSupplyIndex/finSupplyMediaInputIndex.
Some information about the devices lies in the printer mib, e.g. parts of
the
input output and alert table. The finisher devices also have to know e.g.
under
which indexes their own input tables reside in the printer mib.
Therefore the printer and the finisher devices have to get this information,
which is not the case today, or the up3i manager has to merge all tables of
every device together in tables for the whole print line, which could be a
bold venture.
What do you think is the best way for us to implement printer/finisher mib
in
the print line?
Best regards,
Andreas Hirn
_____________________________________
Andreas Hirn OPS TEC
Software Development
Océ Printing Systems GmbH
Siemensallee 2
85586 Poing, Germany
Direct Dial +49-8121-72 4029
Direct Fax +49-8121-72 31 73
mailto: Andreas.Hirn at ops.de
www.oce.com
_____________________________________
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.pwg.org/archives/pmp/attachments/20050228/a147b208/attachment-0001.html